SERVICES
WHAT WE CAN DO FOR YOU
MCS will maintain and retain all dimensional instrument calibration records in accordance to the requirements of ISO/IEC 17025.
MCS provides fully reliable and accurate dimensional instrument calibration service.
Any dimensional instrument calibration request outside the ISO/IEC 17025 Scope of Accreditation for MCS will be serviced by an approved ISO/IEC 17025 compliant vendor.
MCS dimensional Instrument calibration services are performed in accordance with the requirements of ISO/IEC 17025.
MCS can provide full-time and part-time employees at your facility to perform the dimensional cali bration services specified by our clients.
DIMENSIONAL INSTRUMENT
PHYSICAL TEST & MEASURMENT INSTRUMENT
ELECTRICAL PROCESS CONTROL
INSTRUMENTS MCS SERVICES:
Depth Gage | Dial, Digital & Vernier Caliper | Dial & Digital Micrometer | Dial & Digital Indicator | Height Gage | Inside Micrometer
INSTRUMENTS SERVICED BY MCS APPROVED SUPPLIERS:
Air Gage | Amplifier | Angle Block | Angle Plate | Bench Centers | Bore Gage | Chamfer Gage | CMM | Crimper | Digital Readout| Feeler Gage | Gage Block | Glass Scales | Hardness Tester | Height Master | Hole Gage | Laser Micrometer | Level-Bubble | Level - Electronic | Master Setting Plug | Master Setting Ring | Micrometer Standard | Optical Comparator | Optical Flat | Optical Parallels | Parallels | PI Tapes | Pin Gage | Plug Gage | Protractors | Radius Gage | Ring Gage | Ruler | Sine Bar | Snap Gage | Square | Straight Edge | Super-Micrometer | Surface Finish Analyzer | Surface Finish Standard | Surface Plate | Tape Measure | Thickness Gage | Threaded Plug Gage | Threaded Ring Gage | Threaded Wire Gage | Tools Pre-Setters
DIMENSIONAL INSTRUMENT CALIBRATION
ON & OFF SITE SERVICES OFFERED
PHYSICAL TEST & MEASURMENT INSTRUMENT
ON & OFF SITE SERVICES OFFERED
INSTRUMENTS MCS SERVICES:
Pressure Gage | Pressure Recorder | Pressure Transmitter | Torque Driver | Torque Wrench
Pressure: 0-10,000 P.S.I.
Torque: 2.5 to 1000 Lbf-ft.
INSTRUMENTS SERVICED BY MCS APPROVED SUPPLIERS:
Deadweight Tester | Dynamometer | Force Gage | Load Cell | Manometer | Platform Scales | Pressure Source | Tensile Tester | Tensiometer | Weight
Force/Mass: Capability Up to 100,000 Lbs.
Scale & Balance: Capability Up to 5,000 Lbs.
Tension & Compression: Capability Up to 400,000 Lbs.
Pressure & Vacuum: Capability -14.7 to 10,000 P.S.I.
INSTRUMENTS MCS SERVICES:
Pressure Recorder | Pressure Switch | Pressure Transmitter | Process Timers | RTD | Temperature Controller | Temperature Recorder | Temperature Switch | Temperature Transmitter
Pressure: 0-10,000 P.S.I.
Temperature:
Type J, 0 to 75°C Type K, -200 to 1250°C Type T, -200 to 350°C RTD 3& 4 Wire, -200 to 800°C
DC Current: 4 to 20 mA
INSTRUMENTS SERVICED BY MCS APPROVED SUPPLIERS:
Barometer | Deadweight Tester | Dynamometer | Force Gage | Load Cell | Manometer | Platform Scale | Pressure Gage/Transducer | Pressure Recorder | Pressure Source | Tensile Tester | Tensiometer | Weight | Vacuum Gage/Transducer
Force/Mass: Capability Up to 100,000 Lbs.
Scale & Balance: Capability Up to 5,000 Lbs.
Tension & Compression: Capability Up to 400,000 Lbs.
Pressure & Vacuum: Capability -14.7 to 10,000 P.S.I.
ELECTRICAL PROCESS CONTROL
ON & OFF SITE SERVICES OFFERED